Conroe Buying Guide: Feeding the Monster
by Gary Key & Wesley Fink on July 19, 2006 6:20 AM EST- Posted in
- Motherboards
ASUS P5W-DH Deluxe
Basic Features
Current thinking in overclocking options is to provide very fine adjustments for voltages over a very wide range of control - particularly in the memory voltage control. ASUS has done this on other recent boards, like the AM2-based M2N32-SLI Deluxe. However, the P5W-DH only extends to 2.4V compared to the 2.5V on the M2N32-SLI and granularity of the adjustments is a pretty coarse 0.5V compared to 0.2V on the M2N32-SLIl. We suspect this is because the P5W-DH is mainly a refresh to the existing ASUS P5WD2-E, which we reviewed at ASUS P5WD2-E Premium: Intel 975X for the Enthusiast when it was introduced in January.
As you will see below, overclocking was outstanding, but we suspect that higher voltage adjustments on the MCH would allow even higher overclocks. The ASUS stops at 1.65V, while the Intel BadAxe goes on to 1.725V. We would welcome ASUS raising the top voltage on the MCH. There are reports that modding the ASUS to reach 1.9V MCH allows FSB overclocks to almost 500 instead of the current limit of around 440 to 450 FSB.
If you compare the new board to the earlier P5WD2-E you will find the board is basicly the same. The storage controllers have been changed to a Silicon Image that allows a port-multiplier type connect to one of the ICH7 ports. This allows driverless RAID. The board has also dropped the PCIe x4 slot. Asus also replaced the Marvel SATA/PATA controller with the updated JMicron chip. In general. though, our comments in the P5WD2-E review still accurately describe the board's strengths and weaknesses.
The P5W-DH Deluxe adds the lower voltages required by Core 2 Duo and meets the voltage stability requirements for Conroe. Both of these factors are why almost all existing Socket 775 boards cannot handle Core 2 Duo. Both a BIOS and a hardware change are required for proper operation with Conroe.
Basic Performance
All-in-all the ASUS P5W-DH Deluxe is one of the best Conroe boards we have tested. The 975X chipset is definitely more mature than current P965 chipset motherboards. Having said that, there were still several BIOS revisions during our testing to update certain peculiarities in the current steppings of Core 2 Duo.
The ASUS board was every bit as stable with Core 2 Duo as the Intel BadAxe, which for a long time was the only board that would operate with Conroe. The ASUS also implements the ability to adjust X6800 (2.93EE) ratios both up and down, which is a feature of this processor, but is not supported on all boards. The ASUS overclocks further than any other stock board we tested, and it recovers from bad overclocks gracefully. If the OC is close a reboot will usually allow further adjustment. If the OC is far off you need to physically turn off the power then restart to further adjust the BIOS. This is a much more friendly board for OC than the Intel BadAxe, for instance, that will not recover from any failed OC without a full power down and sometimes a CMOS clear.
The ASUS P5W-DH Deluxe also fully supports dual X8 CrossFire. The Enthusiast wanting to overclock Conroe as far as possible or anyone wanting to run ATI multi-GPU on an Intel chipset will be very happy with the P5W-DH. We liked the board enough that it became our new standard board for our DDR2 memory testing platform.
Overclocking
The decision was reached to evaluate motherboards with the E6700 (2.67) processor, as it represents the mid-range of Conroe pricing. Of course, all Conroe processors except for the top X6800 are multiplier locked, which limits options in overclocking. Like Socket 478 that does not appear a huge handicap, since the stock E6700 reached a 50% overclock at 4.0 GHz. Our new OC test bed uses an excellent air cooler in the Tuniq Tower, and you are likely to experience lower overclocks with stock cooling.
The ASUS P5W-DH also reached 4.0GHz with an X6800 (stock 266 x15 at 1.575V) and an E6600 at 445FSB x 9x multiplier. All of these results are outstanding, representing overclocks at stock ratio as high as 67%.
With the wide range of adjustable memory ratios and voltages, memory was set to end up somewhere around DDR2-800 3-3-3-9 at 2.2V. This is really easy with the ASUS P5W-DH BIOS, since the BIOS shows the resulting memory speed when you adjust the FSB speed. This means you don't have to calculate the resulting memory speed when trying to set up a rational overclock, which is a really convenient feature for most enthusiasts.
Overclocking is always dependent on the chip you have and the capabilities of the motherboard. Processors vary in their OC abilities, and OC is never a given. However, we are confident that wherever you can go with your CPU it is not likely the ASUS P5W-DH Deluxe will be holding back your overclocking efforts.
Basic Features
| ASUS P5W-DH Deluxe | |
| Market Segment | High-End/Enthusiast |
| CPU Interface | Socket T (Socket 775) |
| Chipset | Intel 975X + ICH7R |
| CPU Support | Core 2 Duo, Pentium D, Celeron D, Pentium XE, LGA-775 based Pentium 4 |
| Thermal Design | 8-phase power Fan-less Heatpipe Cooling ASUS Stack Cool for OC |
| Default Bus Speed | 1066 (533/266) |
| Bus Speeds | 100 to 500 in 1MHz Increments |
| Memory Speeds | DDR2 at Auto,400,533,667,711,800,889,1067 |
| PCIe Speeds | Auto, 90 to 150 in 1MHz Increments |
| Performance Mode | Auto, Standard Turbo |
| AI Overclocking | Manual, Auto, Overclock Profile, AI N.O.S. |
| PCI | Auto, 33.3, To CPU |
| Core Voltage | Auto, 1.225V (Actual CPU voltage) to 1.7000V in 0.0125V increments |
| FSB Termination Voltage | Auto, 1.2v, 1.3v, 1.4v, 1.5v |
| MCH (Memory Controller Hub) Voltage | Auto, 1.50v, 1.55v, 1.60v, 1.65v |
| ICH (SB) Voltage | Auto, 1.05v, 1.20v |
| PEG Link Mode | Auto, Slow, Normal, Fast, Faster |
| CPU Clock Multiplier | Auto, 4x-25x in 1X increments |
| DRAM Voltage | Auto, 1.8V to 2.4V in .05v increments |
| DRAM Timing Control | 9 Options |
| Hyper Path 3 | Auto, Disabled, Enabled |
| Multi-GPU Option | CrossFire (2 X8 PCIe) |
| Memory Slots | Four 240-pin DDR2 DIMM Slots Dual-Channel Configuration Unbuffered ECC/non ECC Memory to 8GB Total Intel MPT (Memory Pipeline Technology) ASUS HyperPath3 |
| Expansion Slots | 2 PCIe X16 2 PCIe X1 3 PCI Slots |
| Onboard SATA/RAID | 3 SATA2 3Gb/s Drives by Intel ICH7R (RAID 0,1,5) PLUS 2 SATA2 3 Gb/s Drives by JMicronJMB363 (RAID 0,1) (1 internal,1 external) PLUS 2 SATA2 3 Gb/s Drives by Sil4723 (supports RAID 10 by combining iCH7R drives with Sil4723 drives) TOTAL - 7 Sata2 3Gb/s drives |
| Onboard IDE/IDE RAID | One Standard ATA133/100/66 (2 drives) by JMicron JMB363 |
| Onboard USB 2.0/IEEE-1394 | 8 USB 2.0 ports supported by ICH7R 2 Firewire 1394a by TI |
| Onboard LAN | DUAL PCIe Gigabit by Marvel 88E8053 for AI Net2, PLUS WiFi 54Mbps supporting 802.11g |
| Onboard Audio | Azalia HD Audio by Realtek ALC882M 8 channel codec Supports Dolby Master Studio including Dolby Digital Live |
| Power Connectors | 24-pin ATX 4-pin EATX 12V |
| Back Panel I/O Ports | 1 x PS/2 Keyboard 1 x PS/2 Mouse 1 x Serial 1 x Audio I/O Panel (6 plug programmable) 1 x Optical S/PDIF Out Port 1 x Coaxial S/PDIF Out Port 1 x IEEE 1394a Firewire 1 x External SATA2 2 x RJ45 LAN 1 x Wireless LAN antenna 4 x USB |
| BIOS Revision | AMI 701 - July 8, 2006 |
Current thinking in overclocking options is to provide very fine adjustments for voltages over a very wide range of control - particularly in the memory voltage control. ASUS has done this on other recent boards, like the AM2-based M2N32-SLI Deluxe. However, the P5W-DH only extends to 2.4V compared to the 2.5V on the M2N32-SLI and granularity of the adjustments is a pretty coarse 0.5V compared to 0.2V on the M2N32-SLIl. We suspect this is because the P5W-DH is mainly a refresh to the existing ASUS P5WD2-E, which we reviewed at ASUS P5WD2-E Premium: Intel 975X for the Enthusiast when it was introduced in January.
 |
| Click to enlarge |
As you will see below, overclocking was outstanding, but we suspect that higher voltage adjustments on the MCH would allow even higher overclocks. The ASUS stops at 1.65V, while the Intel BadAxe goes on to 1.725V. We would welcome ASUS raising the top voltage on the MCH. There are reports that modding the ASUS to reach 1.9V MCH allows FSB overclocks to almost 500 instead of the current limit of around 440 to 450 FSB.
If you compare the new board to the earlier P5WD2-E you will find the board is basicly the same. The storage controllers have been changed to a Silicon Image that allows a port-multiplier type connect to one of the ICH7 ports. This allows driverless RAID. The board has also dropped the PCIe x4 slot. Asus also replaced the Marvel SATA/PATA controller with the updated JMicron chip. In general. though, our comments in the P5WD2-E review still accurately describe the board's strengths and weaknesses.
The P5W-DH Deluxe adds the lower voltages required by Core 2 Duo and meets the voltage stability requirements for Conroe. Both of these factors are why almost all existing Socket 775 boards cannot handle Core 2 Duo. Both a BIOS and a hardware change are required for proper operation with Conroe.
Basic Performance
All-in-all the ASUS P5W-DH Deluxe is one of the best Conroe boards we have tested. The 975X chipset is definitely more mature than current P965 chipset motherboards. Having said that, there were still several BIOS revisions during our testing to update certain peculiarities in the current steppings of Core 2 Duo.
The ASUS board was every bit as stable with Core 2 Duo as the Intel BadAxe, which for a long time was the only board that would operate with Conroe. The ASUS also implements the ability to adjust X6800 (2.93EE) ratios both up and down, which is a feature of this processor, but is not supported on all boards. The ASUS overclocks further than any other stock board we tested, and it recovers from bad overclocks gracefully. If the OC is close a reboot will usually allow further adjustment. If the OC is far off you need to physically turn off the power then restart to further adjust the BIOS. This is a much more friendly board for OC than the Intel BadAxe, for instance, that will not recover from any failed OC without a full power down and sometimes a CMOS clear.
The ASUS P5W-DH Deluxe also fully supports dual X8 CrossFire. The Enthusiast wanting to overclock Conroe as far as possible or anyone wanting to run ATI multi-GPU on an Intel chipset will be very happy with the P5W-DH. We liked the board enough that it became our new standard board for our DDR2 memory testing platform.
Overclocking
| ASUS P5W-DH Deluxe Overclocking Testbed |
|
| Processor: | Intel Core 2 Duo E6700 Dual Core, 2.67GHz, 4MB Unified Cache 1066FSB, 10x Multiplier |
| CPU Voltage: | 1.525V (default 1.2V) |
| Cooling: | Tuniq Tower 120 Air Cooling |
| Power Supply: | OCZ GameXstream 700W |
| Memory: | Corsair Twin2X2048-PC2-8500C5 (2x1GB) (Micron Memory Chips) |
| Hard Drive | Hitachi 250GB 7200RPM SATA2 16MB Cache |
| Maximum OC: (Standard Ratio) |
400x10 4000MHz (+50%) |
The decision was reached to evaluate motherboards with the E6700 (2.67) processor, as it represents the mid-range of Conroe pricing. Of course, all Conroe processors except for the top X6800 are multiplier locked, which limits options in overclocking. Like Socket 478 that does not appear a huge handicap, since the stock E6700 reached a 50% overclock at 4.0 GHz. Our new OC test bed uses an excellent air cooler in the Tuniq Tower, and you are likely to experience lower overclocks with stock cooling.
The ASUS P5W-DH also reached 4.0GHz with an X6800 (stock 266 x15 at 1.575V) and an E6600 at 445FSB x 9x multiplier. All of these results are outstanding, representing overclocks at stock ratio as high as 67%.
With the wide range of adjustable memory ratios and voltages, memory was set to end up somewhere around DDR2-800 3-3-3-9 at 2.2V. This is really easy with the ASUS P5W-DH BIOS, since the BIOS shows the resulting memory speed when you adjust the FSB speed. This means you don't have to calculate the resulting memory speed when trying to set up a rational overclock, which is a really convenient feature for most enthusiasts.
Overclocking is always dependent on the chip you have and the capabilities of the motherboard. Processors vary in their OC abilities, and OC is never a given. However, we are confident that wherever you can go with your CPU it is not likely the ASUS P5W-DH Deluxe will be holding back your overclocking efforts.
Facebook
Twitter
RSS
123 Comments
View All Comments
Gary Key - Thursday, July 20, 2006 - link
Thank you for the comments. Our focus on the first cooler roundup will be on units that cost under $25 but the Tuniq will be included as a reference point along with the retail Intel unit. Our follow up will include the high end air coolers and some water cooling units.The Tuniq is considered to be one of the best air coolers available at this time although we are starting to see this design being incorporated by other suppliers quickly.
biggersteve - Tuesday, September 19, 2006 - link
Hope you can get an Arctic Cooler Pro 7 into that cooler review. Quiet as a tomb and mighty cool.jonmcguffin - Thursday, July 20, 2006 - link
A feature built into the Core 2 Duo processors is this new Digital Thermal Sensor that supposedly has the ability to provide much quicker and more accurate thermal information about each processor. The key with this though is that it requires support from the motherboard. Why did you guys not mention this feature in any of the motherboards you tested?My guess is that since the P965 was "built" for Core 2 Duo, my guess would be that it supports this feature while the older 975 does not. In going back and forth between pro's and con's of the P965, if this feature is in fact built into the chipset/motherboard, it is worth pointing out. I'm not really an overclocker though I do want to buy a system that will be rock solid in stability for many years to come. Quite PC's that are very reliable and stable are critical and this is a good feature.
Also, you reviewed the Abit AB9 Pro motherboard a few weeks back but somehow it was left out of this overview. At $160 on the street, despite it's layout issue's, this looks to me like perhaps the best board right now for the guy who isn't rich and just wants a very solid Core 2 Duo mobo.
Hope you get a chance to review and respond.
Jon
Gary Key - Thursday, July 20, 2006 - link
Jon,The Gigabyte DQ6 actually has the ability to select readings from either sensor (Digital/Legacy) on the CPU in the power management settings. We will go over this in detail in our full review of the board or other Conroe capable boards in the future. These type of features along with audio and storage performance are not generally not reviewed in the guide articles but covered in the full product reviews.
The Abit AB9-Pro is shaping up to be a very good mid-range board (prices around $142 already) once the bios is complete. We are due to receive bios B6 next week that is optimized for Conroe and allows full memory configuration from both a timing and ratio viewpoint. The board was not ready to be included in the buyers guide until Abit had a final bios to us. We will report the results as soon as we complete testing.
Wesley Fink - Thursday, July 20, 2006 - link
We had planned to include the Abit AB9 in our roundup IF Abit got the memory issue fixed before the review. Unfortunately even the latest beta BIOS we received on Tuesday does not fix the issue. There is no means on the current Abit board to change memory speed or timings. It supposedly reads the SPD and boots at DDR2-533 5-5-5-15 with every dimm we tried. You can't run Value Ram at DDR2-800 for example or run DDR2-800 at rated speed. Or change timings to 3-2-3 at DDR-533 even if you know the ram can run at those timings. We did not think it fair to make a big deal of this in a review since Abit is supposedly working on it, but we see they are now also selling the board at some retailers and memory is still broken as far as we know.We consider this problem, if not fixed, to disqualify the Abit from consideration by any Enthusiast. We plan to do a full review of the Abit AB9 Pro if and when Abit fixes this major problem.
supremelaw - Thursday, July 20, 2006 - link
Jon,Why would more accurate thermal sensors
have high priority, if the Conroe runs
much cooler and more efficiently?
Are you planning extreme O/C, perhaps?
Wouldn't a superior HSF have higher priority?
e.g.:
http://www.supremelaw.org/systems/heatsinks/warnin...">http://www.supremelaw.org/systems/heatsinks/warnin...
Just curious here.
Sincerely yours,
/s/ Paul Andrew Mitchell
Webmaster, Supreme Law Library
http://www.supremelaw.org/">http://www.supremelaw.org/
falc0ne - Wednesday, July 19, 2006 - link
The usual best from Anandtech..I was in a bit of fog if switching to conroe or not, but now I have a mutch more clearer picture. After the part2 of this suite, it will all be clear to me.P.S. Your articles on Nvidia's NForce 4 platform made me choose that platform and AMD64.
My sincere thanks, I owe you a lot
wackypete - Wednesday, July 19, 2006 - link
Thanks for putting this article together. Your effort has not gone unnoticed.Howard - Wednesday, July 19, 2006 - link
Anybody know what chips it uses? The 5-5-5-15 DDR2-667 variety, that is.Gary Key - Wednesday, July 19, 2006 - link
We still have additional memory selections from a variety of suppliers arriving for further memory reviews at this time.