ABOUT BENCH FORUMS PODCAST LOGIN REGISTER
PC Components
Smartphones & tablets
Systems
ENTERPRISE & IT
GUIDES

Socket 754 Roundup, Part 3: Asus, Soltek & DFI

 by Wesley Fink on September 14, 2004 12:03 AM EST
39 Comments | Add A Comment
39 Comments

DFI LANParty UT nF3 250Gb: Overclocking and Stress Testing

FSB Overclocking Results


Front Side Bus Overclocking Testbed
Default Voltage
Processor: Athlon 64 3200+
2.0GHz
CPU Voltage: 1.5V (default)
Cooling: Thermaltake Silent Boost K8 Heatsink/Fan
Power Supply: OCZ Power Stream 520W
Memory: OCZ PC3200 EL Platinum Rev. 2
or Geil PC3200 Ultra X
Maximum OC:
(Standard Ratio)		 248 x 10
2470MHz (+24%)
Maximum FSB:
(Lower Ratio)		 316 x 8 -1:1 Memory, 1 DIMM
270 x 9 at (1:1 Memory, 2 DIMMs)

The DFI LANParty UT nF3 250Gb was recently reviewed in-depth (DFI LANParty UT nF3-250Gb: Overclocker's Dream). Overclocking and Memory Performance charts are included here for easier reference. You should refer to the DFI review for complete information on the board's performance.

Memory Stress Test Results:


Stable DDR400 Timings - 1 DIMMs
(1/3 DIMMs populated - Single-Channel mode)
Clock Speed: 200MHz
CAS Latency: 1.5
RAS to CAS Delay: 2T
RAS Precharge: 10T*
Precharge Delay: 2T
Command Rate: 1T
*Several memory tests have shown that memory performs fastest on the nVidia nForce chipsets at a TRas (RAS Precharge) settings in the 9 to 13 range. We ran our own Memory Bandwidth tests with memtest86 with TRas settings from 5 to 15 at a wide range of different memory speeds. The best bandwidth was consistently at 9 to 11 at every speed, with TRas 10 always in the best range at every speed. The performance improvement at TRas 10 was only 2% to 4% over TRas 5 and 6 depending on the speed, but the performance advantage was consistent across all tests. All benchmarks were run at a TRas setting of 10.

We have not tested a Socket 754 board that offered a CAS 1.5 setting. The OCZ memory ran without problems with 1 DIMM at 1.5-2-2-10 settings.

Stable DDR400 Timings - 2 DIMMs
(2/3 DIMMs populated - Single-Channel mode)
Clock Speed: 200MHz
CAS Latency: 2.0
RAS to CAS Delay: 2T
RAS Precharge: 10T*
Precharge Delay: 2T
Command Rate: 1T

All earlier 754 benchmarks were run with 2 DIMMs, and this is the configuration that was used for all standard benchmark tests. The DFI LANParty UL was completely stable with 2 DIMMs at the rated timings of 2-2-2-10, at default speed.

Filling all three available memory slots is more strenuous on the memory sub-system than testing 2 DIMMs on a motherboard. We were very pleased to find that 3 DS DIMMs (1.5GB) of memory worked fine at timings almost the same as the aggressive timings which we used for 2 DIMMs. The DFI is one of the few Socket 754 boards that we have tested which can handle 3 DS DIMMs. You do need to use slightly slower timings with 3 DIMMs, but the 2-2-3-10 is very close to the rated 2-2-2-10 timings of the memory that we used for testing.

Stable DDR400 Timings - 3 DIMMs
(3/3 DIMMs populated - Single-Channel mode)
Clock Speed: 200MHz
CAS Latency: 2.0
RAS to CAS Delay: 3T
RAS Precharge: 10T*
Precharge Delay: 2T
Command Rate: 2T

The boot screen and Sisoft Sandra 2004 both reported a Command Rate of 2T when all 3 DIMM slots were filled.

DFI LANParty UT nF3 250Gb: Features and Layout Standard Performance Test Configuration
PRINT THIS ARTICLE
Comments Locked

39 Comments

View All Comments

  • Term - Monday, September 27, 2004 - link

    Uhm.. the new ASUS bios fix the OC stability problem with SATA right?

  • Wesley Fink - Saturday, September 18, 2004 - link

    #34 - The Asus K8N-E manual does state 3MB of memory as the maximum capacity. The specifications have been corrected in the review.

  • LocutusX - Thursday, September 16, 2004 - link

    Daxzus,

    For more accurate "real-world advice" concerning the K8N-E, please see the unofficial thread for that mobo at the Anandtech forums. There are people there who have been using it extensively for the last 2 months, who have tried a wide variety of components/overclocking on it.

  • justly - Wednesday, September 15, 2004 - link

    #27 – Wesley
    Thank you for the explanation about your testing methodology, now I feel more comfortable knowing that you do check for these minor deviations when comparing new products against older ones.

    #28 – Wesley (again)
    I agree about it being a shame that SiS seems to always get dumped on by big name motherboard manufactures and that even when a good product hits the street it seems to get forgotten about or overlooked. The thing is I still think you are just as guilty as many others reviewers. If you don’t understand what I mean then just look at #32 (by PrinceGaz) since I would have said the EXACT same thing.
    This might be a little arrogant of me, but would it really hurt to mention their product when talking about a section of the market that they perform so well in (non-overclockers).

  • Daxzus - Wednesday, September 15, 2004 - link

    also...I was wondering if anyone has a good powersupply and case that might work good for me for a good price.

  • Daxzus - Wednesday, September 15, 2004 - link

    I read every thing that was in the review about the 3 diffrent motherboards and I have some questions.

    In the review it was said that the Asus K8N-E deluxe maxed out at 2GB of memory, but at newegg and some all the other places I can buy it from-and even Asus homepage, say that the Asus K8N-E deluxe has a max of 3GB of memory. What this in error in the reveiw or am I looking at buying the wrong board?

    Also I was thinking about buying the Asus K8N-E deluxe and I have a college budget and I was wanting to get some recomendation as to some really good cheap memory to get for it. Also maybe some good budget video cards. I saw that in the review that ATI 9800 was used...wouldn't a Nvidia video card work better considering the chip set?

    but all in all thank for the info that you put into the reviews Fink!

    Dax

  • AtaStrumf - Wednesday, September 15, 2004 - link

    I just hope that your upcoming OC article will at least mention sempron 3100+, since you (AT)did promise to OC it, but untill now you have not done so.

  • PrinceGaz - Wednesday, September 15, 2004 - link

    #28 Wesley Fink-

    From the aricle- "If overclocking is not particularly important to you, then one of the first generation boards based on the VIA chipset might also meet your needs at a lower price."

    And your reply- "There is actually another complaint about Sis. None of the Sis A64 cipsets I have tested, including the 939 Reference Board, have a working PCI/AGP lock."

    If overclocking is not particularly important to someone, the lack of a PCI/AGP lock wouldn't matter.

  • jwix - Wednesday, September 15, 2004 - link

    The article mentions overclocking difficulties with SATA drives with the DFI board being the exception. I wonder....if running 2 drives in a raid 1 config, would it make it any more difficult to overclock on the DFI?

  • LocutusX - Wednesday, September 15, 2004 - link

    "The problem is ports 1 and 2 on nVidia are coupled with the PHY Gigabit LAN and generally will not overclock very well."

    Source?
Copyright © 2024. All rights reserved.
BENCH
TOPICS
FOLLOW
ABOUT

Log in

Don't have an account? Sign up now